Environmental & Reliability Testing
Test Facilities
BE Analytic has established world class test facility for quality and reliability assurance of different Mechanical, Electronic and Electro Mechanical Products. The infrastructure includes climatic testing lab, dynamic testing lab, HALT and HASS. Environmental testing facilities are suitable to perform ESS , Vibration tests, Altitude test, Thermal cycling test, Thermal shock test, Humidity test, High temperature test, Low temperature test, Water Ingress protection tests, Solid Ingress protection tests, Mechanical shock and Bump test, Salt spray test, Drop test and different kinds of environmental tests as per JSS 55555 & MIL-STD, IEC-60529, EN, DIN and IS0-20653, GS 95024-3-1, SAE J1455, ASTM C 150 specifications and determine whether the systems/subsystems perform consistently in the Service environment or not.
BE Analytic also help developing Test plans for Reliability Growth Analysis, Reliability Demonstration, Burn-inn, HALT and HASS screens. Apart from performing compliance related tests, we also do testing of equipment for Failure Mode Analysis and Reliability/MTBF estimation during prototype phases. This help companies identify the failures modes and comparing with warranty goals set, which will in turn reduce cost and time of the product development.
With respect to different standards we perform various kinds of tests in our lab. Tests which we perform are mentioned below:
ALTITUDE (CATH) TEST:
| Chamber Workspace | 800mm x 850mm x 900mm |
| Temperature Range | -70⁰C to 180⁰C ±2⁰C |
| Rate of Change of Temp. | 5°C/min as per IEC 60068-3-5 |
| Humidity Range | 15% TO 95% RH ±3%RH in a Climatic Range of 10°C to 85°C |
| Altitude Range | Atmospheric to 10 mbar ±3mbar |
| Altitude Rate | Atmospheric to 100 mbar within 25-30 minutes Atmospheric to 10 mbar within 40-45 minutes |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1 |
Altitude Test |
MIL-STD 202G (conditions 105C,
A/B/C/F) |
|
2 |
Low Pressure (Altitude) test
|
MIL-STD 810G (condition 500.5) |
|
3 |
High Altitude test, Low Altitude test, Decompression test |
IEC 60068-2-39 |
|
4 |
Combined cold test
|
IEC 60068-2-40 |
|
5 |
Low Air Pressure test
|
JIS W 0812 |
Altitude testing simulates operation, performance and shipment of a product at different altitudes. These tests typically simulate the low air pressure when operating a product at high altitude or shipping a product by air. In order to ensures the safety of the product altitude test is most important.
Altitude test is also called as Low Pressure test, Decompression test, High Altitude test, Low Altitude test, Combined cold test and Low Air Pressure test as per various test standards. BE Analytic will assure that we conduct and perform altitude tests for your products efficiently to reach high quality standards.
VIBRATION TESTING:
| Rated Force | 2500Kgf |
| Frequency Range | 5 to 2500Hz |
| Maximum Acceleration | 100g |
| Maximum Velocity | 1800mm/s |
| Displacement | 51mm |
| Payload Capacity | 350Kg |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Sine on Random |
Sine: IS 9000(Part8) IEC 60068-2-6 MIL-STD-810F JSS 55555: 2012 Rev 1 JSS 50101 JIS D1601 Mixed Mode: IEC 60062-2-80 (Part 2);80 MIL-STD-810G Random: IEC 60068-264 IEC 61373 |
|
2. |
Sine |
|
|
3. |
Random |
|
|
4. |
Mixed |
|
|
5. |
Shock |
|
|
6. |
Bump |
Vibration testing is used to demonstrate a product’s ability to resist dynamic loads, fluctuation without losing critical functional or structural integrity under specified loads. It can be used to identify accumulated stress effects, and the resulting mechanical weaknesses and performance flaws.
We conduct various kinds of vibration tests like, Sine on Random vibration, Sine vibration, Random vibration test, Mixed mode vibration test, Mechanical shock testing, Bump test in our laboratory as per customer requirement.
SINE VIBRATION & MECHANICAL SHOCK TEST:
| Rated Force | 4000 Kgf |
| Frequency Range | 5 to 2000Hz |
| Maximum Acceleration | 160g |
| Maximum Velocity | 2000mm/s |
| Displacement | 70mm |
| Payload Capacity | 500Kg |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Sine on Random |
Sine: IS 9000(Part8) IEC 60068-2-6 MIL-STD-810F JSS 55555: 2012 Rev 1 JSS 50101 JIS D1601 Mixed Mode: IEC 60062-2-80 (Part 2);80 MIL-STD-810G Random: IEC 60068-264 IEC 61373 |
|
2. |
Sine |
|
|
3. |
Random |
|
|
4. |
Mixed |
|
|
5. |
Shock |
|
|
6. |
Bump |
The purpose of vibration tests is to evaluate the effect caused on component parts by vibration in a specified frequency range. We conduct various kinds of vibration tests like, Sine on Random vibration, Sine vibration, Random vibration test, Mixed mode vibration test, Mechanical shock testing, Bump test in our laboratory as per customer requirement.
THERMAL CYCLING TEST:
| Number of Equipment | 2 |
| Chamber Workspace | 1000mm x 1000mm x 1000mm |
| Temperature Range | -65⁰C to 180⁰C |
| Ramp Rate | 10⁰C/Min. Average |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Low Temperature Test |
IEC 60068-2-14 IS 9000 (Part 2) IS 9000 (Part 14) MIL-STD-810F JSS 55555 IEC 60068-2-1 |
|
2. |
Low Temperature Storage |
IEC 60068-2-1 IEC 60068-2-14 JSS 50101 |
|
3. |
Low Temperature Storage Cum
Operation
|
|
|
4. |
Low Temperature Operation |
|
|
5. |
Thermal Cycling |
IEC 60068-2-14 (tests Na &Nb)
IS 9000 (Part 15,Sec I & Sec II)
MIL-STD-810F
JSS 55555 |
Thermal Cycling or Temperature Cycle testing is performed on materials/products to determine the resistance of exposure to alternating extremes of high and low temperatures. Conducting thermal cycling tests during the product development will assist in determining:
- The existence of thermal coefficient mismatches.
- The sensitivity of these mismatches to repeated temperature excursions
BE Analytic offers a range of thermal cycling test services like, Thermal Cycling, Low Temperature Test, Low Temperature Storage, Low Temperature Storage Cum Operation, Low Temperature Operation to simulate different scenarios.
HUMIDITY TEST & DAMP HEAT TEST:
| Chamber Workspace | 750mm x 800mm x 800mm |
| Temperature Range | 20⁰C to 125⁰C ±2⁰C |
| Humidity Range | 30% TO 95% RH ±3%RH |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1 |
Humidity Test
|
IEC 60068-2-78 |
|
2 |
Damp Heat |
IEC 60068-2-30
|
|
3 |
Humidity test / Dew Test
|
MIL-STD-810F |
|
4 |
Steady State Humidity test |
ISO 16750-4
|
|
5 |
Tropical Exposure test |
JSS 55555
|
|
6 |
Damp Heat (Cyclic), Damp Heat (Moisture Resistance)
|
JSS 50101
|
Humidity test is a type of corrosion analysis technique that helps in the determination of corrosion rates in materials. In this test, the material/product is exposed to various environmental factors (temperature and humidity) and corrosive products to study the impact of corrosion to certain industrial materials.
It is a vital part of quality control that is usually performed during the product development in order ensure the safety and quality of the products.
BE Analytic offers a range of thermal cycling test services like Humidity Test, Damp Heat, Tropical Exposure test, Dew Test, Steady state humidity test and Moisture Resistance test as per various Industry standards.
TROPICAL EXPOSURE & DEW TEST:
| Chamber Workspace | 1500mm x 1500mm x 1500mm |
| Temperature Range | 20⁰C to 180⁰C ±2⁰C |
| Humidity Range | 20% TO 98% RH ±3%RH |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1 |
Humidity Test
|
IEC 60068-2-78 |
|
2 |
Damp Heat |
IEC 60068-2-30
|
|
3 |
Humidity test / Dew Test
|
MIL-STD-810F |
|
4 |
Steady State Humidity test |
ISO 16750-4
|
|
5 |
Tropical Exposure test |
JSS 55555
|
|
6 |
Damp Heat (Cyclic), Damp Heat (Moisture Resistance)
|
JSS 50101
|
Tropical Exposure test is a type of humidity test that helps in the determination of corrosion rates in materials. In this test, the material/product is exposed to various environmental factors (temperature and humidity) and corrosive products to study the impact of corrosion to certain industrial materials.
It is a vital part of quality control that is usually performed during the product development in order ensure the safety and quality of the products.
BE Analytic offers a range of thermal cycling test services like Humidity Test, Damp Heat, Tropical Exposure test, Dew Test, Steady state humidity test and Moisture Resistance test as per various Industry standards.
THERMAL SHOCK TEST:
| Basket Size | 450mm x 550mm x 600mm |
| Temperature Range | -65⁰C to 180⁰C |
| Change Over Time | 12 Sec. |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1 |
Thermal Shock test |
IEC 60068-2-14 (tests Na &Nb) IEC 60068-2-30 |
|
2 |
Temperature Shock test
|
MIL-STD-810F
|
|
3 |
Rapid Temperature Cycling test (THERMAL SHOCK)
|
JSS 55555
|
|
4 |
Thermal Shock testing
|
IS 9000 (Part 15,Sec I & Sec II)
|
Thermal shock testing is conducted to determine if equipment can withstand sudden changes in the temperature of the surrounding atmosphere without experiencing physical damage or deterioration in performance. As a result of exposure to sudden temperature changes, operation of the temperature shock test items may be affected either temporarily or permanently. Thermal shock testing reduces the risk of product failure in the field by replicating a quick transition between two extreme temperatures.
BE Analytic offers a range of thermal shock testing services like Thermal Shock, Temperature Shock, Rapid Temperature Cycling (THERMAL SHOCK), Thermal Shock testing as per various Industry standards.
TEMPERATURE / THERMAL SHOCK TESTING:
| Chamber Workspace | 420*420*615 |
| Temperature Range | -65⁰C to 180⁰C |
| Change over time | 12 Sec |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1 |
Thermal Shock test |
IEC 60068-2-14 (tests Na &Nb) IEC 60068-2-30 |
|
2 |
Temperature Shock test
|
MIL-STD-810F
|
|
3 |
Rapid Temperature Cycling test (THERMAL SHOCK)
|
JSS 55555
|
|
4 |
Thermal Shock testing
|
IS 9000 (Part 15,Sec I & Sec II)
|
Thermal shock testing is conducted to determine if equipment can withstand sudden changes in the temperature of the surrounding atmosphere without experiencing physical damage or deterioration in performance. As a result of exposure to sudden temperature changes, operation of the temperature shock test items may be affected either temporarily or permanently. Thermal shock testing reduces the risk of product failure in the field by replicating a quick transition between two extreme temperatures.
BE Analytic offers a range of thermal shock testing services like Thermal Shock, Temperature Shock, Rapid Temperature Cycling (THERMAL SHOCK), Thermal Shock testing as per various Industry standards.
HIGH TEMPERATURE TEST:
| Chamber Workspace | 500mm x 500mm x 500mm |
| Temperature Range | Ambient to 180⁰C, ±2⁰C |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
High Temperature Test |
IEC 60068-2-1 IEC 60068-2-14 IS 9000 (Part 3) IS 9000 (Part 4) MIL-STD-810F JSS 55555 ISO 16750-4 JSS 50101 |
|
2. |
High Temperature Storage |
|
|
3. |
High Temperature Storage
Cum Operation |
|
|
4. |
High Temperature
Operation
|
|
|
5. |
Power on Burn-In Test |
|
High temperature testing reduces the risk of product failure in the field by simulating the temperature conditions that products are exposed to during their lifetime. The test specification defines the applied temperatures and test conditions, these may be to test the equipment’s operational limits or to test the equipment’s survivability at more extreme storage temperatures.
BE Analytic offers a range of testing services like High Temperature Test, High Temperature Storage Test, High Temperature Storage Cum Operation Test, High Temperature Operation Test, Power on Burn-In Test as per various Industry standards.
HIGH TEMPERATURE STORAGE TEST:
| Chamber Workspace | 1000mm x 1000mm x 1000mm |
| Temperature Range | Ambient to 180⁰C, ±2⁰C |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
High Temperature Test |
IEC 60068-2-1 IEC 60068-2-14 IS 9000 (Part 3) IS 9000 (Part 4) MIL-STD-810F JSS 55555 ISO 16750-4 |
|
2. |
High Temperature Storage |
|
|
3. |
High Temperature Storage
Cum Operation |
|
|
4. |
High Temperature
Operation
|
|
High temperature storage test reduces the risk of product failure in the field by simulating the temperature conditions that products are stored in high temperature conditions for a long time during their lifetime. The test specification defines the applied temperatures and test conditions, these may be to test the equipment’s operational limits or to test the equipment’s survivability at more extreme storage temperatures.
BE Analytic offers a range of testing services like High Temperature Test, High Temperature Storage Test, High Temperature Storage Cum Operation Test, High Temperature Operation Test, Power on Burn-In Test as per various Industry standards.
BURN-IN TEST:
| Chamber Workspace | 800mm x 800mm x 900mm |
| Temperature Range | Ambient to 200⁰C, ±2⁰C |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
High Temperature Test |
IEC 60068-2-1 IEC 60068-2-14 IS 9000 (Part 3) IS 9000 (Part 4) MIL-STD-810F JSS 55555 ISO 16750-4 JSS 50101 |
|
2. |
High Temperature Storage |
|
|
3. |
High Temperature Storage
Cum Operation |
|
|
4. |
High Temperature
Operation
|
|
|
5. |
Power on Burn-In Test |
|
Burn-In test is conducted to check product condition in the field by simulating the temperature conditions that products are stored in high temperature in power on conditions for a long time during their lifetime. The test specification defines the applied temperatures and test conditions, these may be to test the equipment’s operational limits or to test the equipment’s survivability at more extreme storage temperatures.
BE Analytic offers a range of testing services like High Temperature Test, High Temperature Storage Test, High Temperature Storage Cum Operation Test, High Temperature Operation Test, Power on Burn-In Test as per various Industry standards.
LOW TEMPERATURE TEST:
| Chamber Workspace | 800mm x 800mm x 900mm (W*D*H) |
| Humidity Range | 30% to 98% RH |
| Temperature Range | -70⁰C to 200⁰C |
| Ramp Rate | 10⁰C/Min. Average |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Low Temperature Test |
IEC 60068-2-14 IS 9000 (Part 2) IS 9000 (Part 14) MIL-STD-810F JSS 55555 IEC 60068-2-1 |
|
2. |
Low Temperature Storage
|
JSS 50101 IEC 60068-2-1 IEC 60068-2-14 |
|
3. |
Low Temperature Storage Cum Operation |
|
|
4. |
Low Temperature Operation |
|
|
5. |
Thermal Cycling |
IEC 60068-2-14 (tests Na &Nb) IS 9000 (Part 15,Sec I & Sec II) MIL-STD-810F JSS 55555 |
Low temperature test reduces the risk of product failure in the field by simulating the temperature conditions that products are stored in low temperature conditions for a long time during their lifetime. The test specification defines the applied temperatures and test conditions, these may be to test the equipment’s operational limits or to test the equipment’s survivability at more extreme storage temperatures.
BE Analytic offers a wide range of testing services like Low Temperature Test, Low Temperature Storage Test, Low Temperature Storage Cum Operation Test, Low Temperature Operation Test as per various Industry standards.
SALT SPRAY, SALT FOG, SALT CORROSION TESTING:
| Chamber Workspace | 300 litres |
| Temperature Range | Ambient to 50°C |
| Ramp Rate | 2°C/min |
| Humidity Range | 95-100%RH |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Salt Spray Test Salt corrosion test Cyclic Salt Spray and Humidity Test Salt spray humidity test Salt Fog test |
IEC 60068-2-11 IEC 60068-2-52 IS 9000 (Part 2) ASTM B 117 Rev A MIL-STD-810F JSS 55555 JIS Z 2731 |
|
2. |
Mixed Gas test |
IEC 60068-2-60 |
Salt Spray test / Salt corrosion testing reduces the risk of product failure in the field by simulating equipment’s ability to withstand the effects of corrosion and to give a general indication of corrosion resistance.
Salt Spray test is a corrosion testing method that uses high-saline environments to measure the corrosion resistance of products, paints and coatings over extended periods.
BE Analytic offers a wide range of testing services like Salt spray test, Cyclic salt spray and humidity test, Salt corrosion test and Salt fog test as per various Industry standards.
BE Anlaytic also conducts Mixed gas test is an accelerated environmental corrosion aging test that provides contact with harsh chemical pollutants commonly found in the atmosphere. The test specifically evaluates the corrosion of electrical components due to exposure to atmospheric gasses and contaminants. This test allows manufacturers to test for the build-up of corrosion that leads to the reduced performance of electrical components, providing an accelerated environment to determine a product’s life span as well as identify potential failure points. These results allow manufacturers to reduce premature wear and liability.
DUST TEST & SAND TEST (Solid Ingression Protection Test) :
| Chamber Workspace | 1000*1000*1000 mm |
| Test Type | Dust Ingress Protection |
| Air Flow Rate | Upto18m/s |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Dust Ingress Protection IP5X- Limited Ingress Protection IP6X- Dust Tight Protection IP5K- Dust Protected IP6K- Dust Tight |
IEC 60529 ISO 20653 |
|
2. |
IP1X- Solid Foreign Object50mm Diameter Sphere |
|
|
3. |
IP2X- Solid Foreign Object12mm Diameter Test Finger |
|
|
4. |
IP3X- Solid Foreign Object2.5mm Steel Wire |
|
|
5. |
IP4X- Solid Foreign Object1mm Steel Wire |
Dust test and Sand test are the types of Ingress protection (IP) testing reduces the risk of product failure in the field by assessing the degree of protection provided against mechanical intrusion, dust, accidental contact and water into casings and enclosures.
BE Analytic offers a wide range of solid IP testing services like IP1X, IP2X, IP3X, IP4X, IP5X,IP6X, IPX6K as per various Industry standards.
RAIN TEST (Water Ingression Protection Test):
| Chamber Workspace | 1000*1000*1000 mm |
| Test Type | Water Ingress Protection |
| SL.No. | Specific Test Perform | Water Flow Rate | Pressure | Rotating Speed of Table | Test Duration |
|---|---|---|---|---|---|
|
1. |
IPX1- Dripping Water |
1mm/min,
±0.5 |
NA |
1 RPM |
10 min |
|
2. |
IPX2- Dripping Water
when tilted up to 15° |
3mm/min,
±0.5 |
NA |
1 RPM |
2.5 min for
each tilt
position |
|
3. |
IPX3- Spraying Water
up to 60° Angle |
0.7 L/min,
±0.5% per
hole |
80 to
100kPa |
1 RPM |
5 min |
|
4. |
IPX4- Splashing Water
in all direction |
10 L/min,
±0.5% per
hole |
80 to
100kPa |
1 RPM |
5 min |
|
5. |
IPX5- Powerful Water
Jet with Low Pressure |
12.5 L/min |
30kPa |
1 RPM |
3 min |
|
6. |
IPX6- Powerful Water
Jet with High Pressure |
100 L/min |
1000kPa |
1 RPM |
3 min |
|
7. |
IPX6K- Powerful Water
Jet with Extremely High
Pressure |
75L/min |
1000kPa |
1RPM |
3 min |
Rain test and Water tests are the types of Ingress protection (IP) testing reduces the risk of product failure in the field by assessing the degree of protection provided against mechanical intrusion, dust, accidental contact and water into casings and enclosures.
BE Analytic offers a wide range of water IP testing services like IPX1, IPX2, IPX3, IPX4, IPX5,IPX6, IPX6K as per various Industry standards.
IMMERSION TEST (IPX7 & IPX8):
| Chamber Workspace | 1000*1000*1000 mm |
| Test Type | Water Ingress ProtectionImmersion Test |
| SL.No. | Specific Test Perform | Water Level | Test Method Specification against which tests are performed | Test Duration |
|---|---|---|---|---|
|
1. |
IPX7 |
Up to 1m |
IEC 60529 ISO 20653 |
30 min |
|
2. |
IPX8 |
Deeper than
1m
|
As Per
Customer
Needs |
Immersion tests are the types of Ingress protection (IP) testing reduces the risk of product failure in the field by assessing the degree of protection provided against mechanical intrusion, dust, accidental contact and water into casings and enclosures.
BE Analytic offers a wide range of water IP testing services like IPX7, IPX8, as per various Industry standards.
HIGH PRESSURE JET/ WASH TEST (IPX9K):
| Chamber Workspace | 720*780*500 mm(L*B*H) |
| Test Type | Water Ingress Protection |
| SL.No. | Specific Test Perform | Water Flow Rate | Water Temperature | Pressure | Rotating Speed of Table | Test Duration | Test Method Specification against which tests are performed |
|---|---|---|---|---|---|---|---|
|
1. |
IPX9KPowerful High
Temperature
Water Jets |
14-16 |
80ºC ± 5°C
Deviating
temperatures may
be agreed |
80-100 bar |
5 RPM |
30 Sec/
Nozzle |
IEC 60529 ISO 20653 |
High Pressure Wash / IPX9K test is one of the type of Ingress protection (IP) testing reduces the risk of product failure in the field by assessing the degree of protection provided against mechanical intrusion, dust, accidental contact and water into casings and enclosures. In this test product is tested with hot water of higher temperature which is sprayed on to the product surface with extreme pressure condition to check the capability of the product stability.
BE Analytic offers a wide range of water IP testing services like IPX9K, High pressure jet stream test, High pressure wash test as per various Industry
WATER SPRAY TEST (IPX4K):
| SL.No. | Specific Test Perform | Water Flow Rate (LPM) | Water Temperature | Water Pressure at Rain or Spray Nozzle (Gauge Pressure) | Number of Rain or Spray Nozzle | Test Duration | Test Method Specification against which tests are performed |
|---|---|---|---|---|---|---|---|
|
1. |
Spray Test –
S1 |
24.5 |
Ordinary
Temperature |
0.10 Mpa |
40 |
As Per
Customer
Need |
JIS D 0203 |
|
2. |
Spray TestS2 |
39.2 |
Ordinary
Temperature |
0.30MPa |
40 |
As Per
Customer
Need |
JIS D 0203 |
Water spray test / IPX4K test is one of the type of Ingress protection (IP) testing reduces the risk of product failure in the field by assessing the degree of protection provided against mechanical intrusion, dust, accidental contact and water into casings and enclosures. In this test product is tested with water, through the holes of a oscillating tube which is sprayed on to the product surface to check the capability of the product stability.
BE Analytic offers a wide range of water IP testing services like IPX4K, Oscillating water test, JIS test as per various Industry
BUMP TEST:
| Maximum Acceleration | 100g |
| Bump (Pulse) Duration | 3 to 18 milli second |
| Bump rate control | 1 to 3 Bump per second. |
| Payload Capacity | 100 Kg |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Bump Test |
JSS 55555: 2012 Rev 1 JSS 50101 JIS D1601 MIL-STD-810G |
The Bump test is a vibration analysis technique that allows us to identify resonances and propose modifications in machine structures and components to alter their natural frequencies or even design dynamic vibration absorbers to attenuate resonant energy.
BE Analytic offers Bump test facility as per customer needs.
DROP TEST & BENCH HANDLING TEST:
| Testing Height (Drop Height) | Minimum 380mm & Maximum 1800mm |
| Max. Dimension of Box to be tested | 500*500*500 mm (L*W*H) |
| Max. Weight of Box to be tested | 60 Kg |
| Base Dimension (Floor) | 1200 * 900 mm |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1 |
Drop Test, Transit drop test |
MIL STD 810G |
|
2 |
Toppling test
|
JSS 55555
|
|
3 |
Bench Handling test
|
MIL STD 810G
|
Drop test is used to evaluate how well the product design and materials will perform when it is exposed to an amount of external impact force. It is the best way to determine whether a product is suitable for use in environments where this kind of impact might happen
Drop testing our products gives us an opportunity to make alterations and modifications before our products go into market. It means we can confidently say that this product will provide acceptable standards or protection if an accident were to happen.
BE Analytic offers Drop test, Toppling test and Bench handling test facility as per customer needs.
COLD WATER SPRAY TEST:
| Chamber Workspace | 1500mm x 1500mm x 1500mm |
| Chamber Temp Range | 20ºC to 180ºC |
| Water Temp Range | 0 to 4ºC |
| Humidity Range | 20% TO 98% RH ±3%RH |
The Ice-water test / cold water splash test is used to check the product performance testing in the splashed areas on vehicles such as automotive exterior instruments and parts. In the process of driving, especially when driving on wet roads in winter, the impact of frozen mud water will occur. Cold water thermal shock test is to simulate the splash of cold water on hot systems/components through equipment.
BE Analytic offers Ice-water test / cold water splash test facility as per customer needs.
OZONE TEST:
| Chamber Workspace | 600mm X 600mm X 600mm |
| Temperature Range | 15⁰C to 45⁰C ±5⁰C |
| Humidity Range | 25% TO 65% RH ±5%RH |
| Ozone Concentration Level | 0.1 PPM to 9 PPM ±5%RH |
| Sensor Type | Electro-Chemical type |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Ozone Test |
ASTM D 518 IS-3400 (Part-20) ASTM D 1149 ISO 1431-1 : 1989 ASTM D 1171 ASTM D 3395 ASTM D 4575 BIS, ISO, DIN, MIL |
Ozone testing is a method used to determine a rubber or elastomer’s resistance to ozone degradation. The elastomer samples are placed in a special chamber that exposes them to ozone at concentration and duration specified by a testing specification or standard.
BE Analytic offers ozone test facility as per customer needs.
FUNGUS TEST / MOLD GROWTH TESTING:
| Testing Height (Drop Height) | Minimum 380mm & Maximum 1800mm |
| Max. Dimension of Box to be tested | 500*500*500 mm (L*W*H) |
| Max. Weight of Box to be tested | 60 Kg |
| Base Dimension (Floor) | 1200 * 900 mm |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Mould Growth Test,
Fungus Test
|
JSS 55555: 2012,
MIL-STD-810G
DO 160
|
Fungus test / Mold Growth test is used to assesses the products’ ability to resist Fungus (mold) growth in elevated moisture conditions. Manufacturers can use fungus resistance testing results to guide them toward developing products that resist mold growth.
BE Analytic offers Fungus test / Mold Growth test facility as per customer needs.
