Chambers
Altitude (Cath) Chamber
| Chamber Workspace | 800mm x 850mm x 900mm |
| Temperature Range | -70⁰C to 180⁰C ±2⁰C |
| Rate of Change of Temp. | 5°C/min as per IEC 60068-3-5 |
| Humidity Range | 15% TO 95% RH ±3%RH in a Climatic Range of 10°C to 85°C |
| Altitude Range | Atmospheric to 10 mbar ±3mbar |
| Altitude Rate | Atmospheric to 100 mbar within 25-30 minutes Atmospheric to 10 mbar within 40-45 minutes |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Altitude Test |
MIL-STD 202G (conditions 105C,
A/B/C/F) MIL-STD 810G (condition 500.5) IEC 60068-2-39 IEC 60068-2-40 RTCA/DO-160F JIS W 0812 |
Ozone Test Chamber
| Chamber Workspace | 600mm X 600mm X 600mm |
| Temperature Range | 15⁰C to 45⁰C ±5⁰C |
| Humidity Range | 25% TO 65% RH ±5%RH |
| Ozone Concentration Level | 0.1 PPM to 9 PPM ±5%RH |
| Sensor Type | Electro-Chemical type |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Ozone Test |
ASTM D 518 IS-3400 (Part-20) ASTM D 1149 ISO 1431-1 : 1989 ASTM D 1171 ASTM D 3395 ASTM D 4575 BIS, ISO, DIN, MIL |
Humidity Chamber
| Chamber Workspace | 750mm x 800mm x 800mm |
| Temperature Range | 20⁰C to 125⁰C ±2⁰C |
| Humidity Range | 30% TO 95% RH ±3%RH |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Damp Heat Test
(or)
Tropical Exposure Test
(or)
Humidity Test
(or)
Dew Test |
IEC 60068-2-78 IEC 60068-2-30 IEC 60068-2-67 IS 9000 (Part 4) IS 9000 (Part 5) MIL-STD-810F JSS 55555 ISO 16750-4 JSS 50101 |
Humidity Chamber
| Chamber Workspace | 1500mm x 1500mm x 1500mm |
| Temperature Range | 20⁰C to 180⁰C ±2⁰C |
| Humidity Range | 20% TO 98% RH ±3%RH |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Damp Heat Test
(or)
Tropical Exposure Test
(or)
Humidity Test |
IEC 60068-2-78 IEC 60068-2-30 IEC 60068-2-67 IS 9000 (Part 4) IS 9000 (Part 5) MIL-STD-810F JSS 55555 ISO 16750-4 JSS 50101 |
Thermal Cycling Chamber
| Number of Equipment | 2 |
| Chamber Workspace | 1000mm x 1000mm x 1000mm |
| Temperature Range | -65⁰C to 180⁰C |
| Ramp Rate | 10⁰C/Min. Average |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Low Temperature Test |
IEC 60068-2-14 IS 9000 (Part 2) IS 9000 (Part 14) MIL-STD-810F JSS 55555 IEC 60068-2-1 |
|
2. |
Low Temperature Storage |
IEC 60068-2-1 IEC 60068-2-14 JSS 50101 |
|
3. |
Low Temperature Storage Cum
Operation
|
|
|
4. |
Low Temperature Operation |
|
|
5. |
Thermal Cycling |
IEC 60068-2-14 (tests Na &Nb)
IS 9000 (Part 15,Sec I & Sec II)
MIL-STD-810F
JSS 55555 |
Climatic Chamber
| Chamber Workspace | 800mm x 800mm x 900mm (W*D*H) |
| Humidity Range | 30% to 98% RH |
| Temperature Range | -70⁰C to 200⁰C |
| Ramp Rate | 10⁰C/Min. Average |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Low Temperature Test |
IEC 60068-2-14 IS 9000 (Part 2) IS 9000 (Part 14) MIL-STD-810F JSS 55555 IEC 60068-2-1 |
|
2. |
Low Temperature Storage
|
JSS 50101 IEC 60068-2-1 IEC 60068-2-14 |
|
3. |
Low Temperature Storage Cum Operation |
|
|
4. |
Low Temperature Operation |
|
|
5. |
Thermal Cycling |
IEC 60068-2-14 (tests Na &Nb) IS 9000 (Part 15,Sec I & Sec II) MIL-STD-810F JSS 55555 |
Thermal Shock Chamber
| Basket Size | 450mm x 550mm x 600mm |
| Temperature Range | -65⁰C to 180⁰C |
| Change Over Time | 12 Sec. |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Thermal Shock /
Rapid Change of
Temperature with
Prescribed Time of
Transfer |
IEC 60068-2-14 (tests Na &Nb) IS 9000 (Part 15,Sec I & Sec II) MIL-STD-810F JSS 55555 |
Thermal Chamber Oven
| Chamber Workspace | 500mm x 500mm x 500mm |
| Temperature Range | Ambient to 180⁰C, ±2⁰C |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
High Temperature Test |
IEC 60068-2-1 IEC 60068-2-14 IS 9000 (Part 3) IS 9000 (Part 4) MIL-STD-810F JSS 55555 ISO 16750-4 JSS 50101 |
|
2. |
High Temperature Storage |
|
|
3. |
High Temperature Storage
Cum Operation |
|
|
4. |
High Temperature
Operation
|
|
|
5. |
Power on Burn-In Test |
|
High Temperature Chamber
| Chamber Workspace | 1000mm x 1000mm x 1000mm |
| Temperature Range | Ambient to 180⁰C, ±2⁰C |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
High Temperature Test |
IEC 60068-2-1 IEC 60068-2-14 IS 9000 (Part 3) IS 9000 (Part 4) MIL-STD-810F JSS 55555 ISO 16750-4 |
|
2. |
High Temperature Storage |
|
|
3. |
High Temperature Storage
Cum Operation |
|
|
4. |
High Temperature
Operation
|
|
Hot Air Oven Chamber
| Chamber Workspace | 800mm x 800mm x 900mm |
| Temperature Range | Ambient to 200⁰C, ±2⁰C |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
High Temperature Test |
IEC 60068-2-1 IEC 60068-2-14 IS 9000 (Part 3) IS 9000 (Part 4) MIL-STD-810F JSS 55555 ISO 16750-4 JSS 50101 |
|
2. |
High Temperature Storage |
|
|
3. |
High Temperature Storage
Cum Operation |
|
|
4. |
High Temperature
Operation
|
|
|
5. |
Power on Burn-In Test |
|
Salt Spray Chamber
| Chamber Workspace | 300 litres |
| Temperature Range | Ambient to 50°C |
| Ramp Rate | 2°C/min |
| Humidity Range | 95-100%RH |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Salt Spray Test /
Cyclic Salt Spray
and Humidity Test/
Salt spray humidity
test |
IEC 60068-2-11 IEC 60068-2-52 IS 9000 (Part 2) ASTM B 117 Rev A MIL-STD-810F JSS 55555 JIS Z 2731 |
|
2. |
Mixed Gas test |
|
Dust Test Chamber (Ingress Protection)
| Chamber Workspace | 1000*1000*1000 mm |
| Test Type | Dust Ingress Protection |
| Air Flow Rate | Upto18m/s |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Dust Ingress Protection IP5X- Limited Ingress Protection IP6X- Dust Tight Protection IP5K- Dust Protected IP6K- Dust Tight |
IEC 60529 ISO 20653 |
|
2. |
IP1X- Solid Foreign Object50mm Diameter Sphere |
|
|
3. |
IP2X- Solid Foreign Object12mm Diameter Test Finger |
|
|
4. |
IP3X- Solid Foreign Object2.5mm Steel Wire |
|
|
5. |
IP4X- Solid Foreign Object1mm Steel Wire |
Water Test Chamber (Ingression Protection)
| Chamber Workspace | 1000*1000*1000 mm |
| Test Type | Water Ingress Protection |
| SL.No. | Specific Test Perform | Water Flow Rate | Pressure | Rotating Speed of Table | Test Duration |
|---|---|---|---|---|---|
|
1. |
IPX1- Dripping Water |
1mm/min,
±0.5 |
NA |
1 RPM |
10 min |
|
2. |
IPX2- Dripping Water
when tilted up to 15° |
3mm/min,
±0.5 |
NA |
1 RPM |
2.5 min for
each tilt
position |
|
3. |
IPX3- Spraying Water
up to 60° Angle |
0.7 L/min,
±0.5% per
hole |
80 to
100kPa |
1 RPM |
5 min |
|
4. |
IPX4- Splashing Water
in all direction |
10 L/min,
±0.5% per
hole |
80 to
100kPa |
1 RPM |
5 min |
|
5. |
IPX5- Powerful Water
Jet with Low Pressure |
12.5 L/min |
30kPa |
1 RPM |
3 min |
|
6. |
IPX6- Powerful Water
Jet with High Pressure |
100 L/min |
1000kPa |
1 RPM |
3 min |
|
7. |
IPX6K- Powerful Water
Jet with Extremely High
Pressure |
75L/min |
1000kPa |
1RPM |
3 min |
Rectangular Fibre Tank
| Chamber Workspace | 1000*1000*1000 mm |
| Test Type | Water Ingress ProtectionImmersion Test |
| SL.No. | Specific Test Perform | Water Level | Test Method Specification against which tests are performed | Test Duration |
|---|---|---|---|---|
|
1. |
IPX7 |
Up to 1m |
IEC 60529 ISO 20653 |
30 min |
|
2. |
IPX8 |
Deeper than
1m
|
As Per
Customer
Needs |
Spray Test Facility (IPX4)
| SL.No. | Specific Test Perform | Water Flow Rate (LPM) | Water Temperature | Water Pressure at Rain or Spray Nozzle (Gauge Pressure) | Number of Rain or Spray Nozzle | Test Duration | Test Method Specification against which tests are performed |
|---|---|---|---|---|---|---|---|
|
1. |
Spray Test –
S1 |
24.5 |
Ordinary
Temperature |
0.10 Mpa |
40 |
As Per
Customer
Need |
JIS D 0203 |
|
2. |
Spray TestS2 |
39.2 |
Ordinary
Temperature |
0.30MPa |
40 |
As Per
Customer
Need J |
JIS D 0203 |
Electro Dynamic Vibration Shaker
| Rated Force | 2500Kgf |
| Frequency Range | 5 to 2500Hz |
| Maximum Acceleration | 100g |
| Maximum Velocity | 1800mm/s |
| Displacement | 51mm |
| Payload Capacity | 350Kg |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Sine on Random |
Sine: IS 9000(Part8) IEC 60068-2-6 MIL-STD-810F JSS 55555: 2012 Rev 1 JSS 50101 JIS D1601 Mixed Mode: IEC 60062-2-80 (Part 2);80 MIL-STD-810G Random: IEC 60068-264 IEC 61373 |
|
2. |
Sine |
|
|
3. |
Random |
|
|
4. |
Mixed |
|
|
5. |
Shock |
|
|
6. |
Bump |
Electro Dynamic Vibration Shaker
| Rated Force | 4000 Kgf |
| Frequency Range | 5 to 2000Hz |
| Maximum Acceleration | 160g |
| Maximum Velocity | 2000mm/s |
| Displacement | 70mm |
| Payload Capacity | 500Kg |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Sine on Random |
Sine: IS 9000(Part8) IEC 60068-2-6 MIL-STD-810F JSS 55555: 2012 Rev 1 JSS 50101 JIS D1601 Mixed Mode: IEC 60062-2-80 (Part 2);80 MIL-STD-810G Random: IEC 60068-264 IEC 61373 |
|
2. |
Sine |
|
|
3. |
Random |
|
|
4. |
Mixed |
|
|
5. |
Shock |
|
|
6. |
Bump |
Bump Test Machine
| Maximum Acceleration | 100g |
| Bump (Pulse) Duration | 3 to 18 milli second |
| Bump rate control | 1 to 3 Bump per second. |
| Payload Capacity | 100 Kg |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Bump Test |
JSS 55555: 2012 Rev 1 JSS 50101 JIS D1601 MIL-STD-810G |
Drop Tester
| Testing Height (Drop Height) | Minimum 380mm & Maximum 1800mm |
| Max. Dimension of Box to be tested | 500*500*500 mm (L*W*H) |
| Max. Weight of Box to be tested | 60 Kg |
| Base Dimension (Floor) | 1200 * 900 mm |
| SL.No. | Specific Test Perform | Test Method Specification against which tests are performed |
|---|---|---|
|
1. |
Drop Test |
MIL STD 810G JSS 55555 |
Cold Water Spray Test
| Chamber Workspace | 1500mm x 1500mm x 1500mm |
| Chamber Temp Range | 20ºC to 180ºC |
| Water Temp Range | 0 to 4ºC |
| Humidity Range | 20% TO 98% RH ±3%RH |
